The client reads <pet a> as its active pet's database ID with
GetInt64Attribute (LWOPetControlComponent::LoadFromSaveData 0x00c18120);
DLU never wrote it. Live wrote a="0" on every character (226 live
charxmls, 45 with pets): the charxml is only read when the player loads,
before any pet is out, and a pet summoned afterwards registers itself
(RegisterPetDBID). So a is written as 0.
The pet taming type p@t stays 0 as DLU already wrote it: it is an int
(IntAttribute), the client sets it to 0 for every pet it is given
(AddPetToPlayer in LWOPetControlComponent::HandleMessage 0x00d0fe00,
which ignores the message's elemental type) and every live pet had t="0".
Commented so it isn't "fixed" later.
Check in game: with a tamed pet, summon it, change zones and log out and
back in: the pet menu and pet naming work as before and no pet is shown
as out until you summon one.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The client reads the cooldowns still running from the charxml on load
(LWOSkillComponent::LoadFromSaveData 0x00c2a9c0): <skil sc="..."> split
on ';' and ':' (the delimiter string at 0x015b1714 is L";:") into a
cooldown group and the seconds left, each put in its cooldown map under
{hasCooldownGroup = 1, group}, the key it checks when the player casts a
skill of that group (0x00c11400). Live wrote <skil/> with nothing running
and e.g. <skil sc="17:15.6958;"/> otherwise (226 live charxmls; groups
8, 17 and 78 seen, the times below the groups' SkillBehavior cooldowns).
The claude-client-re-docs page described sc as "id;time" pairs; the
live saves and the delimiters show "group:time;".
DLU wrote no <skil>, so relogging or changing zones cleared every
cooldown (e.g. the 90 s imagination and faction skills).
- A player's successful cast (CastPlayerSkill) starts its
SkillBehavior.cooldowngroup's cooldown (groups 0 and up, cooldown > 0),
counted down in Update.
- Saved as live wrote it; loaded back when the player's SkillComponent
is created, so a cooldown survives several zone changes. Old saves
without <skil> load with none running.
Check in game: use a skill with a long cooldown (e.g. a faction kit's
special skill, a consumable with a cooldown), change zones or log out and
back in right away: its cooldown is still shown and counts down from
where it was (minus the loading time on the server).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The client sends SetTooltipFlag (469: bFlag, then the tooltip,
2 live packets, both tooltip 24) when a tooltip has been shown, and
follows it with SetFlag for the same ID. DLU dropped it and never wrote
char@ttip, so the client's tooltip bits reset on every load.
- SetTooltipFlag message struct and handler: the bit is set or cleared on
the CharacterComponent exactly as the client does it
(LWOCharacterComponent::SendMessage 0x00d34330): tooltips above 127 are
ignored, set = 1 << tooltip, clear = mask ~1 << tooltip (which also
clears the lower bits), shifts of 64 or more give 0.
- Saved as char@ttip, a 64-bit value (the client reads it with
GetLongLongValue in LoadFromSaveData 0x00ca4910). Live wrote it on
every character (226 live charxmls: "0" or "16777216" = tooltip 24).
Old saves without it load with 0.
Check in game: on a new character, trigger a first-time tooltip (e.g.
the one about an item or a new area), change zones and log out and back
in: the character loads normally and the same tooltip does not come back.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The client sends SetMissionTypeState (851) for the journal's mission
types and subtypes (Missions.defined_type / defined_subtype) at load and
after mission updates: 650 live packets, every one with the optional
state left at NEW, the subtype written before the type. DLU
dropped it and never wrote the states, so the client lost them on every
load.
- SetMissionTypeState message struct and handler: the state is stored on
the player's MissionComponent (byte-sized as the client keeps it,
LWOMissionComponent::msgSetMissionTypeState 0x00c90d00).
- Saved as live wrote it (226 live charxmls): after <cur>,
<ts><type v="Build"><st sub="" val="1"/></type>...</ts>, <ts/> when
empty. Read back per <type>; old saves without <ts> load with none.
The client's reader (0x00d171c0) reads v from <ts> rather than from
each <type>, so it files every state under one type; the server keeps
the types apart.
- Mission::SetMissionTypeState (on accept) records NEW for the mission's
type instead of doing nothing.
Check in game: accept missions of a few kinds (a location mission, a
battle achievement), open the passport/journal, then log out and back in
and change zones: the journal tabs keep their "new" markers as before,
nothing errors, and the character still loads.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
