Adds initial support for H100 and its alarmmodule.
Also implements the following modules for T315:
* reportmodule (reporting interval)
* battery
* humidity
* temperature
* Initialize children's modules (and features) using the child component negotiation results
* Set device_type based on the device response
* Print out child features in cli 'state'
* Add --child option to cli 'command' to allow targeting child devices
* Guard "generic" features like rssi, ssid, etc. only to devices which have this information
Note, we do not currently perform queries on child modules so some data may not be available. At the moment, a stop-gap solution to use parent's data is used but this is not always correct; even if the device shares the same clock and cloud connectivity, it may have its own firmware updates.
If a handshake session becomes invalid the device returns 403 on send and an `AuthenticationError` is raised which prevents a retry, however a retry would be successful. In HA this causes devices to go into reauth flow which is not necessary.
With the move towards autodetecting available features, there is no reason to keep SmartPlug around.
kasa.smart.SmartPlug is removed in favor of kasa.smart.SmartDevice which offers the same functionality.
Information about auto_off can be accessed using Features of the AutoOffModule on supported devices.
Co-authored-by: Steven B. <51370195+sdb9696@users.noreply.github.com>
Adds auto-off implementation. The feature stays enabled after the timer runs out, and it will start the countdown if the device is turned on again without explicitly disabling it.
New features:
* Switch to select if enabled: `Auto off enabled (auto_off_enabled): False`
* Setting to change the delay: `Auto off minutes (auto_off_minutes): 222`
* If timer is active, datetime object when the device gets turned off: `Auto off at (auto_off_at): None`
The initial steps to modularize the smartdevice. Modules are initialized based on the component negotiation, and each module can indicate which features it supports and which queries should be run during the update cycle.
This adds a generic interface for all device classes to introspect available device features,
that is necessary to make it easier to support a wide variety of supported devices with different set of features.
This will allow constructing generic interfaces (e.g., in homeassistant) that fetch and change these features without hard-coding the API calls.
`Device.features()` now returns a mapping of `<identifier, Feature>` where the `Feature` contains all necessary information (like the name, the icon, a way to get and change the setting) to present and change the defined feature through its interface.
* Fix for P100 on fw 1.1.3 login_version none
* Fix coverage
* Add delay before trying default login
* Move devtools and fixture out
* Change logging string
Co-authored-by: Teemu R. <tpr@iki.fi>
* Fix test
---------
Co-authored-by: Teemu R. <tpr@iki.fi>
* Fix discovery cli to print devices not printed during discovery
* Fix tests
* Fix print exceptions not being propagated
* Fix tests
* Reduce test discover_send time
* Simplify wait logic
* Add tests
* Remove sleep loop and make auth failed a list
* Separate fake protocols for iot and smart
* Move control_child impl into its own method
* Organize schemas into correct places
* Add test_childdevice
* Add missing return for _handle_control_child
* Add ChildDevice and ChildProtocolWrapper
* Initialize & update children
* Fix circular imports
* Add dummy_protocol fixture and tests for unwrapping responseData
* Use dummy_protocol for existing smartprotocol tests
* Move _ChildProtocolWrapper to smartprotocol.py
* Use dummy_protocol for test multiple requests
* Use device_id instead of position for selecting the child
* Fix wrapping for regular requests
* Remove unused imports
* tweak
* rename child_device to childdevice
* Fix import
* Enable batching of multiple requests
* Test for debug enabled outside of loop
* tweaks
* tweaks
* tweaks
* Update kasa/smartprotocol.py
Co-authored-by: Teemu R. <tpr@iki.fi>
* revert
* Update pyproject.toml
* Add batch test and make batch_size configurable
---------
Co-authored-by: J. Nick Koston <nick@koston.org>
Co-authored-by: Teemu R. <tpr@iki.fi>
* Allow raw-command and wifi without update
* Call update always but on wifi&raw-command
* Add tests
* Skip update also if device_family was defined, as device factory performs an update
* dump_devinfo improvements
* Scrub only the last three bytes for mac addresses
* Add --target to allow creating fixtures based on discovery
* Save fixtures directly to correct location, add --basedir to allow defining the location of repository root
* Add --autosave to disable prompting for saving
* Update fixtures for devices I have
* Add fixture for HS110 hw 4.0 fw 1.0.4
* Improve help strings
* Fix tests
* Update devtools README
* Default to discovery if no host/target given
* Fix connection indeterminate state on cancellation
If the task the query is running in it cancelled, we do
know the state of the connection so we must close. Previously
we would not close on BaseException which could result
in reading the previous response if the previous query was
cancelled after the request had been sent
* add test for cancellation
* Avoid linear search for emeter realtime and emeter_today
Most of the time the data we want is at the end of the
list so we now search backwards to avoid having to
scale all the data and throw most of it away
* more tweaks
* coverage
* coverage
* preen
* coverage
* branch cover
* Pull has_emeter property up to tapodevice base class
This will also use the existence of energy_monitoring in the component_nego query to decide if the device has the service.
* Move emeter related functions to tapodevice
* Remove supported_modules override for now
This should be done in a separate PR, if we want to expose the available components to cli and downstreams
* Dedent extra reqs
* Move extra_reqs initialization
* Fix tests
* Do login entirely within AesTransport
* Remove login and handshake attributes from BaseTransport
* Add AesTransport tests
* Synchronise transport and protocol __init__ signatures and rename internal variables
* Update after review
- Show discovery results for unsupported devices and devices that fail to authenticate.
- Rename `--show-unsupported` to `--verbose`.
- Remove separate `--timeout` parameter from cli discovery so it's not confused with `--timeout` now added to cli command.
- Add tests.
* Add KP125M fixture. Enable tapo auth in pytest.
* authentication is not just for tapo
* Use "##MASKEDNAME##" base64 for nickname and ssid.
---------
Co-authored-by: Teemu R. <tpr@iki.fi>
* Add support for tapo light bulbs
* Use TapoDevice for on/off
* Add tapobulbs to discovery
* Add partial support for effects
Activating the effect does not work as I thought it would,
but this implements rest of the interface from SmartLightStrip.
* Add missing __init__ for tapo package
* Make mypy happy
* Add docstrings to make ruff happy
* Implement state_information and has_emeter
* Import tapoplug from kasa.tapo package
* Add tapo L530 fixture
* Enable tests for L530 fixture
* Make ruff happy
* Update fixture filename
* Raise exceptions on invalid parameters
* Return results in a wrapped dict
* Implement set_*
* Reorganize bulbs to iot&smart, fix tests for smarts
* Fix linting
* Fix BULBS_LIGHT_STRIP back to LIGHT_STRIPS
* Add support for TAPO/SMART KLAP and seperate transports from protocols
* Add tests and some review changes
* Update following review
* Updates following review
