Merge branch 'master' into DetectAndAutoLoadEthernetDrivers

README.md

@@ -164,6 +164,45 @@ The next time you boot your camera, make sure your USB Ethernet Adapter is conne
 
 ---
 
+Network Interface Bonding Support
+
+```
+BONDING_ENABLED="false"
+BONDING_PRIMARY_INTERFACE="eth0"
+BONDING_SECONDARY_INTERFACE="wlan0"
+BONDING_LINK_MONITORING_FREQ_MS="100"
+BONDING_DOWN_DELAY_MS="5000"
+BONDING_UP_DELAY_MS="5000"
+```
+
+Bonding description is best described here:
+https://wiki.debian.org/Bonding#Configuration_-_Example_2_.28.22Laptop-Mode.22.29:
+
+("Laptop-Mode")
+
+Tie cable and wireless network interfaces (RJ45/WLAN) together to define a single, virtual (i.e. bonding) network interface (e.g. bond0).
+As long as the network cable is connected, its interface (e.g. eth0) is used for the network traffic. If you pull the RJ45-plug, ifenslave switches over to the wireless interface (e.g. wlan0) transparently, without any loss of network packages.
+After reconnecting the network cable, ifenslave switches back to eth0 ("failover mode").
+From the outside (=network) view it doesn't matter which interface is active. The bonding device presents its own software-defined (i.e. virtual) MAC address, different from the hardware defined MACs of eth0 or wlan0.
+The dhcp server will use this MAC to assign an ip address to the bond0 device. So the computer has one unique ip address under which it can be identified. Without bonding each interface would have its own ip address. 
+
+BONDING_PRIMARY_INTERFACE
+Specifies the interface that should be the primary.  Typically "eth0".
+
+BONDING_SECONDARY_INTERFACE
+Specifies the interface that should be the secondary.  Typically "wlan0".
+
+BONDING_LINK_MONITORING_FREQ_MS
+Specifies the MII link monitoring frequency in milliseconds. This determines how often the link state of each slave is inspected for link failures.
+
+BONDING_DOWN_DELAY_MS
+Specifies the time, in milliseconds, to wait before disabling a slave after a link failure has been detected. This option is only valid for the miimon link monitor. The downdelay value should be a multiple of the miimon value; if not, it will be rounded down to the nearest multiple.
+
+BONDING_UP_DELAY_MS
+Specifies the time, in milliseconds, to wait before enabling a slave after a link recovery has been detected. This option is only valid for the miimon link monitor. The updelay value should be a multiple of the miimon value; if not, it will be rounded down to the nearest multiple.
+
+---
+
 USB Direct Support:
 
 ```

SD_ROOT/wz_mini/bin/upgrade-run.sh

@@ -12,29 +12,31 @@ exec > >(busybox tee -a ${LOG_FILE}) 2>&1
 
 setup() {
 
-echo "Create Upgrade directory"
+echo "Create Upgrade staging directory"
-mkdir /opt/Upgrade
+mkdir /opt/.Upgrade
 
 echo "Create backup files directory"
-mkdir /opt/Upgrade/preserve
+mkdir /opt/.Upgrade/preserve
 
 echo "Download latest master"
-wget --no-check-certificate https://github.com/gtxaspec/wz_mini_hacks/archive/refs/heads/master.zip -O /opt/Upgrade/wz_mini.zip; sync
+wget --no-check-certificate https://github.com/gtxaspec/wz_mini_hacks/archive/refs/heads/master.zip -O /opt/.Upgrade/wz_mini.zip; sync
 
-echo "Extract archive"
+echo "Extract master archive"
-unzip /opt/Upgrade/wz_mini.zip -d /opt/Upgrade/
+unzip /opt/.Upgrade/wz_mini.zip -d /opt/.Upgrade/
 
-echo "Verify file integrity"
+echo "Verify extracted file integrity"
-cd /opt/Upgrade/wz_mini_hacks-master
+cd /opt/.Upgrade/wz_mini_hacks-master
 md5sum -c file.chk
 
 if [ $? -eq 0 ]; then
-	echo "files OK"
+	echo "File verification successful!"
+	echo "Move staging directory to perform upgrade"
+	mv /opt/.Upgrade/ /opt/Upgrade/
 	install_upgrade_script
 else
-	echo "Failure: archive has corrupted files"
+	echo "Failure: Extracted files may be corrupt.  Aborting upgrade."
-	echo "Delete failed upgrade dir"
+	echo "Delete failed upgrade staging directory"
-	rm -rf /opt/Upgrade
+	rm -rf /opt/.Upgrade
 	exit 1
 fi
 
@@ -98,6 +100,19 @@ fi
 
 echo "UPGRADE MODE"
 
+echo "Verify extracted file integrity"
+cd /opt/Upgrade/wz_mini_hacks-master
+md5sum -c file.chk
+
+if [ $? -eq 0 ]; then
+        echo "File verification successful!"
+else
+        echo "Failure: Extracted files may be corrupt.  Aborting upgrade."
+        echo "Delete failed upgrade directory"
+        rm -rf /opt/Upgrade
+        exit 1
+fi
+
 if [ -f /opt/wz_mini/tmp/.T20 ]; then
 	echo "Upgrading kernel"
 	flashcp -v /opt/Upgrade/wz_mini_hacks-master/v2_install/v2_kernel.bin /dev/mtd1
@@ -133,6 +148,7 @@ reboot
 
 if [[ "$1" == "unattended" ]]; then
 	echo "Unattended upgrade!"
+	rm -rf /opt/.Upgrade
 	rm -rf /opt/Upgrade
 	sync
 	setup
@@ -149,11 +165,12 @@ else
 		read -r -p "${1:-wz_mini, this will download the latest version from github and upgrade your system.  Are you sure? [y/N]} " response
 			case "$response" in
 			[yY][eE][sS]|[yY])
-			if [[ -d /opt/Upgrade ]]; then
+			if [[ -d /opt/.Upgrade ]]; then
 				echo "WARNING: Old Upgrade directory exists"
 				read -r -p "${1:-Unable to proceed, must DELETE old Upgrade directory, are you sure? [y/N]} " response
 				case "$response" in
 				[yY][eE][sS]|[yY])
+				rm -rf /opt/.Upgrade
 				rm -rf /opt/Upgrade
 				sync
 				setup

SD_ROOT/wz_mini/etc/dnsmasq.conf

@@ -0,0 +1,15 @@
+listen-address=127.0.0.1
+port=53
+bind-interfaces
+user=root
+group=root
+pid-file=/var/run/dnsmasq.pid
+domain-needed
+bogus-priv
+dns-forward-max=150
+cache-size=1000
+neg-ttl=3600
+no-poll
+resolv-file=/opt/wz_mini/etc/resolv.dnsmasq
+#log-facility=-
+#log-queries

SD_ROOT/wz_mini/etc/resolv.dnsmasq

@@ -0,0 +1,4 @@
+#List your desired upstream dns servers here
+
+#nameserver 8.8.8.8
+#nameserver 8.8.4.4

file.chk

@@ -1,5 +1,6 @@
 72349f3e54a44146d63dc775d37045b1  SD_ROOT/factory_t31_ZMC6tiIDQN
 d41d8cd98f00b204e9800998ecf8427e  SD_ROOT/wz_mini/mnt/.gitignore
+28cf061770da7b83fbc3752c455a02c3  SD_ROOT/wz_mini/etc/dnsmasq.conf
 34c6a4c3a941ff2becd9f487826d7692  SD_ROOT/wz_mini/etc/uvc.config
 ad7d1a2f9db3079617731b5854ce3b6a  SD_ROOT/wz_mini/etc/init.d/wz_cam.sh
 0774518c06d6ef8e7181d35f194777cc  SD_ROOT/wz_mini/etc/init.d/wz_init.sh
@@ -12,6 +13,7 @@ e3034eac02d8eda9902ca9cf89f0a586  SD_ROOT/wz_mini/etc/inittab
 2c2df1b9cb603f9c31c46162d6ac307f  SD_ROOT/wz_mini/etc/alsa/alsa.conf
 9e5591da95042bcca910403bde25dc60  SD_ROOT/wz_mini/etc/fstab
 c838ac76efbe3d3fc3c4805789a6519f  SD_ROOT/wz_mini/etc/uvc_jxf23.config
+f08b7b96247b3ebd74eee451370d22db  SD_ROOT/wz_mini/etc/resolv.dnsmasq
 d41d8cd98f00b204e9800998ecf8427e  SD_ROOT/wz_mini/etc/configs/.gitignore
 d0541c45c77ad3c5f27f06f03547c4f2  SD_ROOT/wz_mini/etc/shadow
 c838ac76efbe3d3fc3c4805789a6519f  SD_ROOT/wz_mini/etc/uvc_v2.config
@@ -43,13 +45,14 @@ c5d2801b7117b8db6275647110e6c8f1  SD_ROOT/wz_mini/bin/iwconfig.sh
 78aaf46b312749d71c1f93a97f80fa74  SD_ROOT/wz_mini/bin/nm
 02c62618633915a282a547411524ed3c  SD_ROOT/wz_mini/bin/v4l2rtspserver
 a9b8e51b956806e27021e6524ba917ed  SD_ROOT/wz_mini/bin/ranlib
+2393ba8bfe8c86775b8eb7b40fa2fe57  SD_ROOT/wz_mini/bin/dnsmasq
 c23e3da466dc9701bee036ec034583b7  SD_ROOT/wz_mini/bin/rsync
 ff5a2354e4be9cc244f3ac8f304e930a  SD_ROOT/wz_mini/bin/size
 a8970288e72c871bff6a4484f1e733d6  SD_ROOT/wz_mini/bin/readelf
 41b56bb30f02bce5f5e2598073151e16  SD_ROOT/wz_mini/bin/ffmpeg
 e37474a12d76cae16336476cba61e8b8  SD_ROOT/wz_mini/bin/neofetch
 7fcc716cda1e024dae1045050a135beb  SD_ROOT/wz_mini/bin/audioplay_t31
-03a42f7f175f88903c0dc52013f11205  SD_ROOT/wz_mini/bin/upgrade-run.sh
+18acd856dd104377c35ca6121409f9cf  SD_ROOT/wz_mini/bin/upgrade-run.sh
 e6a6a9dd8ce138686083a3d4303cea40  SD_ROOT/wz_mini/bin/iperf3
 0468ffb319707687557353242a518923  SD_ROOT/wz_mini/bin/wg
 65510c6c4d0db4b4679fc92d1c617fdd  SD_ROOT/wz_mini/bin/rtmp-stream.sh
@@ -186,3 +189,7 @@ bd383994491e4bdca81788c168feb2eb  SD_ROOT/wz_mini/lib/libasound.so.2
 f6f0d5a9ebd916de6bdb9695067809ae  SD_ROOT/wz_mini/lib/libaudioProcess.so
 aa102e670336c6bf165f1a9925d9d4fc  SD_ROOT/wz_mini/wz_mini.conf
 d41d8cd98f00b204e9800998ecf8427e  SD_ROOT/wz_mini/tmp/.gitignore
+00b99816217a740f5169709ef01eddf6  v2_install/compile_image.sh
+ff15869fe24297b9a5f75335a458a44f  v2_install/fw_tool.sh
+9625b325d7cf317bc9bc796312be82db  v2_install/v2_kernel.bin
+f01d641b98388e273c1f0ba682ebc75b  v2_install/.gitignore